Liked Forum Posts
|
RE: SR3 Rear Brake Lights source @rjbender Thanks good suggestion I hadn't realised as most over here are the round lights - yes I am looking for the round lights I have a RS |
In forum Alternate Parts / Source |
1 year ago |
|
RE: SR3 XX Radio (PTT) System And 12 Volt Tap Pigtails Attachment : Radio.jpg Hi Cheddar, Attached is the section from the owners manual on the pin out for the radio plug. Hope that helps! |
In forum How To / DIY Discussions |
1 year ago |
|
GDU refresh/service interval Hi, I'm looking at purchasing a SR3 RS, can anyone advise me of the recommended interval for refreshing/service/ rebuild of the GDU. Many thanks |
In forum SR3 Specific Discussions |
1 year ago |
|
RE: Ozarks is amazing Yes, empty water tanks for shade for the corner folks! And note the extended LED light boards that extend over the track into the line of sight. Such a great solution, especially on a busy track with... |
In forum Track / Race Videos |
1 year ago |
|
RE: Ozarks is amazing That looks like a fun track! |
In forum Track / Race Videos |
1 year ago |
|
RE: Ozarks is amazing Wow, not a lot of room for error there ! |
In forum Track / Race Videos |
1 year ago |
|
Ozarks is amazing Took a Radical (#1351) to Ozarks International Raceway in central Missouri last weekend. For those who have not been, it is an exceptional track, only a few years old, and one of my favorite in the co... |
In forum Track / Race Videos |
1 year ago |
|
Radiator Fan doesen't work Hey guys, at the last race, I noticed that my radiator fan wasn't turning on anymore. We applied 12V directly to the fan to test it, and it worked. Can someone explain to me how the fan is controlled?... |
In forum SR8 Specific Discussion |
1 year ago |
|
Rear adjustable pushrod upgrade - what length? For those of you with an SR3 and adjustable rear pushrods, please can you advise what length pushrod you have so I can buy the correct one? I know it's 3/8" UNF, and my original fixed pushrod measures... |
In forum How To / DIY Discussions |
1 year ago |
|
Driveshat splines, to lube or not? I'm not sure whether these are meant to go in dry, both GDU and wheelhub sides, or should I apply some anti seize? If so what products do you folks use? |
In forum How To / DIY Discussions |
1 year ago |
|
RE: GDU pump test and case removal @rjbender having just installed the GDU again today....yes it makes absolutely no sense to remove it from underneath. I installed it back in today with relative ease going in from the top with all th... |
In forum General Discussion |
1 year ago |
|
RE: No first gear thus no neutral At the 14 minute and 35 second mark he's installing the input shaft... At first when he's putting it in neutral position and spinning it it appears that the output shaft is not spinning as is a coup... |
In forum SR3 Specific Discussions |
1 year ago |
|
RE: No first gear thus no neutral 2nd gear was seized to the shaft Attachment : PXL_20250713_043624996.jpg Attachment : PXL_20250713_043630109.jpg |
In forum SR3 Specific Discussions |
1 year ago |
|
RE: SR3 Fuel Pressure loss, cars dies on track Just close this out.... The pump had come loose from bottom of tank and was floating around. That caused the fuel starvation. Then it ultimately had the positive power feed contact the baffles in t... |
In forum General Discussion |
1 year ago |
|
Putting bodywork on/taking off I struggle with putting on/taking off the bodywork. I bought some suction cups on Amazon and they work great for this! Attachment : IMG_9439.jpeg Attachment : IMG_9438.jpeg |
In forum General Discussion |
1 year ago |