Forum Replies Created
|
RE: SR3 RSX Oil Temp Sensor Failure and GDU Temp Sensor Install... @rjbender It's a Bosch (as mentioned by David). At Amazon: AmazonSmile: Bosch 0280130069 OEM Temp Sensor for Select 1987-1995 Porsche: 928; Saab 9000; Volvo: 240, 244, 245, 740, 760, 780, 940 : Automo... |
In forum How To / DIY Discussions |
3 years ago |
|
RE: Big Brakes Can anyone confirm that the big brake package fits the SR3 and SR8? |
In forum SR 10 Specific Discussion |
3 years ago |
|
RE: Source for quiet muffler carbon repack kit? @bluefunelement Good deal. I use the SS stuff as well, and it lasts forever. |
In forum General Discussion |
3 years ago |
|
RE: Source for quiet muffler carbon repack kit? @bluefunelement I get my stuff here: Muffler Repack Kits | Burns Stainless |
In forum General Discussion |
3 years ago |
|
RE: CAN topology of the XX PDM, GPS, Camera and steering wheel @proto Nicely done. I've done similar work with an ECUMaster PMU16 emulating a MoTeC PDM to a MoTeC M150. Once you get how CAN works, the sky's the limit. Please do post your CAN configurations, I'd l... |
3 years ago | |
|
RE: Bearing failure Very interesting. Run the engine a bit hotter, and use higher viscosity oil to keep low oil pressure warnings at bay. |
In forum SR3 Specific Discussions |
3 years ago |
|
RE: Tying down a radical @bill-snead Mac's makes the best tie-downs and ratchets around. Professional Tie Down Systems for Any Vehicle | macscustomtiedowns |
In forum Towing / Trailers / Truck Discussion |
3 years ago |
|
RE: Time to change Wheel Nuts? @meatman All my wheel nuts look like that. I love Rod's work on his, but I think your wheel nuts are fine as is. |
In forum General Discussion |
4 years ago |
|
RE: inspection/should do @rjbender That's really nice work. My wheel nuts and wheel surfaces look very much like your "before" pictures and seem to work ok. But it does concern me when I look at it. I have found that any lub... |
In forum SR3 Specific Discussions |
4 years ago |
|
RE: New 1500cc Hayabusa engine starts briefly then dies Nicely done Wisko Racing! |
In forum General Discussion |
4 years ago |
|
RE: New 1500cc Hayabusa engine starts briefly then dies @davidf That's it. I'm out of ideas. 🙂 This has always felt like the ECU didn't know what the engine was doing. So disconnecting and reconnecting the TPS sensor might have been the fix. Or perhaps you... |
In forum General Discussion |
4 years ago |
|
RE: New 1500cc Hayabusa engine starts briefly then dies Is the inlet air temp sensor in the air box? If so, was the temp sensor connected during your previous testing? |
In forum General Discussion |
4 years ago |
|
RE: Updated "Identifying Radical Model Years By Chassis Number" Guide @charleyhradicalsportscarregistry-com LOL! Of course you're right! It was chassis 42, not 47. |
In forum General Discussion |
4 years ago |
|
RE: Updated "Identifying Radical Model Years By Chassis Number" Guide Thanks Charley! This was interesting for me as my SR800047 (the red one now owned by Joe Poland @joep) is actually a 2008 MY. I had been told it was a 2007. I have to revise my memories now! |
In forum General Discussion |
4 years ago |
|
RE: SR8 half shaft Hi Joe! On Quaife boxes, the inboard tripode "cups" bolt in place, but the Hewland cups are slip-fit. On the outboard side at the wheels, the cups bolt in place. The axles can plunge in either direct... |
In forum General Discussion |
4 years ago |