Forum Replies Created
|
RE: Notes on throttle body balancing, TPS, idle, and throttle adjustment Hello I have a Sr3 with jenvey injection and it's hard to start when cold. My car is hard to start when cold even after 24 v conversion. If you miss the first cold start you can remove and dry the spa... |
In forum How To / DIY Discussions |
4 weeks ago |
|
RE: Blipper Shifter Diagnosistic I finally cut the ignition at the 2*87 connector of the relay and it works fine now |
In forum SR3 Specific Discussions |
1 month ago |
|
RE: Blipper Shifter Diagnosistic Today I tried to cut the ignition coil wire one by one and didn't find one cutting of the engine. 2 wires are signal but the 2 other wires don't stop the engine. I don't know what to do more. Attac... |
In forum SR3 Specific Discussions |
1 month ago |
|
RE: Blipper Shifter Diagnosistic Hello Im installing a VAC robotics paddle shift system. The pneumatic actuator of the kit have a 40 mm stroke (+20mm and -20mm) I checked with the manual gearbox we need +15mm up shift /-15mm down sh... |
In forum SR3 Specific Discussions |
1 month ago |
|
RE: Need help to identify this floating discs and Bell + cross reference Hi Thanks for searching for me ! I finally found another solution. Keep this 280mm discs , Cleaned the bells where they are damaged and made 20 oversized T slot like that we no longer have excess of s... |
In forum Alternate Parts / Source |
2 months ago |
|
Vac robotic paddle shift installation Hello I'm installing a vac robotic pneumatic shifting and it's a pleasure to make this modification. Not yet finished but work is in progress. I can share the DXF/ step files of the brackets. I have a... |
In forum How To / DIY Discussions |
2 months ago |
|
Need help to identify this floating discs and Bell + cross reference Hello I own a SR3 earlier models. on the front I assume they converted to 280 mm discs. But now the bells are damaged and the discs are mooving too much. What is the tolerance of "jeu" ? i can insert ... |
In forum Alternate Parts / Source |
2 months ago |
|
RE: refreshing my first rs3 ( drive shaft) Attachment : cardan5.png Attachment : cardan6.png |
In forum How To / DIY Discussions |
2 months ago |
|
RE: refreshing my first rs3 ( drive shaft) my shafts looks ok they have new cv joints but the right one (the long one) needs few degrees of rotation before to engage. its hard to explain I will try to find the good words.I see that the tripo... |
In forum How To / DIY Discussions |
2 months ago |
|
RE: SR3 car cover does anyone know where to find this ? Attachment : bache.jpg |
In forum SR3 Specific Discussions |
2 months ago |
|
RE: dual battery conversion I would like to say a big thank you to Jim King because your help was great and I managed to convert my sr3 to a dual battery . thanks nico |
In forum General Discussion |
2 months ago |
|
RE: How to connect Coolant sensor mxl strada. Hi I compared the wiring with the oil temp sensor and now i can say that: wiring side of car wirind side of sensor yellow----------------------->Red white------------------------>white... |
3 months ago | |
|
RE: warning light wt high even when engine cold ? Hi I compared the wiring with the oil temp sensor and now i can say that: wiring side of car wirind side of sensor yellow----------------------->Red white------------------------>white... |
In forum SR3 Specific Discussions |
3 months ago |
|
RE: How to connect Coolant sensor mxl strada. Attachment : IMG-20251222-WA0006.jpeg |
3 months ago | |
|
How to connect Coolant sensor mxl strada. Hello my sr3 haven't anymore the connectors on the coolant sensor and I have standard sensor on hose. I have too a used sensor 100 ohms I guess it's an original one from aim but have only 2 wires. Can... |
3 months ago |