Radical Sportscar Registry

CharleyH .

CharleyH .
CharleyH .
This user account status is Approved
About About
Posts Posts
Comments Comments
Forums Forums
Ask the Radical Factory #9 – Hi there I have 2 sr3’s with Life ECU’s (a 2009 and a 2010) that are new to me. I am unable to get ecu data off both cars, so I think it’s something I’m doing. I go thru the prompts and make up the file for the Life data for the car. The computer is properly plugged into the car, main switch on, ignition on. I go to where it says auto read, or just read, all seems to work and comes up with the download screen but then at the bottom I’m meet with a red message: > “no logged data to download happens on both cars what am I doing wrong? Aim data works fine. From Jack A. in Australia
1 year ago in: "Ask the Radical Factory" no comments
Ask the Radical Factory #8 – Hey guys, after sustaining some minor front end damage recently, I’m looking to change my nose cone from a SR3 SS (Gen 1 – Chassis 150) over to a SR3 RS (Gen 2) shape. Will the Crash box underneath need to be changed also? And will the later nose cone line up with the other bodywork panels? Regards, James P
1 year ago in: "Ask the Radical Factory" no comments
Ask the Radical Factory #7 – I bought a SR3RSX 2016, I started it and during warm up it was at 80C on the temp. I gave it a couple small revs prolly up to 4 K , the dash display completely turn red at about between 2500 & 4000 Rpm.it was operating properly at idle or up to 2000 Rpm. I just shut it down to find out what is the issue. Can you advise. Thank you, Ken F
2 years ago in: "Ask the Radical Factory" no comments
Ask the Radical Factory #6 – There’s a lot of conjecture around use of noise killing cans like Supertrapps, decibel devils, and so on. Some people say they are not good for prolonged use due to the back pressure, others say it’s fine but will cut power dramatically. Are they ok to use, and if so, for how long? Are there any you’ve tested out in the field which work, and could you recommend any? Thanks, Raj (@rojid)
2 years ago in: "Ask the Radical Factory" no comments
Ask the Radical Factory Question #5 – Can the Radical version of the Aim SW4 steering wheel used on the SR10 be adapted for use on earlier SR3 and SR8 cars with the Life ECU?
2 years ago in: "Ask the Radical Factory" no comments
Ask the Radical Factory Question #4 – Hello, I Have a new to me a 2009 sr3 (chassis #438). Two questions I have are where about in the setting range for the dampers is a good place to start for a high speed fairly smooth track (CTMP (Mosport) in Canada)? The dampers are the intrax racing with the single adjustment knob at the top car has medium Nik link bars front and rear. Second what set up difference change between the Michelin and Hankook radical tires? The car came with a set of each, and I am free to run either in the club racing that I am doing. cheers, Corey Bradburn
3 years ago in: "Ask the Radical Factory" no comments
Ask the Factory Question #3 – Buongiorno, I am writing from Italy and am the owner of two radicals. I would like to have information on the construction date of the SR4 031 and Prosport 066 chassis. Grazie, Giuseppe Bellini
3 years ago in: "Ask the Radical Factory" no comments
Ask The Factory Question # 2 – I have a 2017 RXC Spyder with a Ford EcoBoost twin turbo engine and noticed that the water pump is starting to go out. Can the water pump be replaced without pulling the motor and drive line? Jeff P.
3 years ago in: "Ask the Radical Factory", Uncategorized no comments
Ask the Factory Q#1 – I am writing to you from Japan. I work in automotive maintenance. I am working on a Radical SR4 engine that will not start. The fuel pump and ignition coil are not working either. I want to check if the engine control module is working properly. Can I have a wiring diagram for the Radical SR4 (Chassis No: SR4 00082j) Best regards, Atsushi K.
3 years ago in: "Ask the Radical Factory" no comments
Ask Phil #14 – Hello Phil, I have a question regarding HD axles for an SR3 RS or RSX. Unfortunately, as you know, we cannot purchase any specifics parts for these axles from Radical, only complete units. Several of us have sourced the tripods to GKN, but we cannot find the specific inner CV hub that was used… Can you guide us in the right direction? Thanks in advance for your assistance. David I. (@hawkster)
3 years ago in: "Ask Phil" no comments
load more posts