Forum Replies Created
|
RE: Which Laptop and Where To Get Downloads From? I use a relatively cheap Windows laptop. I find it helpful if the laptop has a USB-A port and ethernet port built in, otherwise you need a dongle. Not a crisis but one less thing to have if possible. ... |
In forum General Discussion |
1 hour ago |
|
RE: Updating firmware in PDM etc I update the firmware based on the AIM software, never had an issue. See page 53 of their data manual here: |
In forum General Discussion |
2 hours ago |
|
RE: Sudden loss of electrical power I had a similar issue which was related to power connections in PDM box and the cable would come loose during cornering. Once I got those tightened up all was better. To figure it out we took out the ... |
In forum General Discussion |
2 weeks ago |
|
Easier way to get to front splitter bolts? Has anyone devised an easier way to mount/unmount the front splitter? It is a pain to get to the 5 bolts on the bottom that hold the spillter to the chassis. My struggle is to hold the bottom bolts ti... |
In forum General Discussion |
2 weeks ago |
|
RE: Anyone Use The Oil Preheater For Oil Change? I am sure it would work. I use my oil heater 80% of the time I run the car.. plug it in for 45 min, then fire it up. It still needs to warm up the water and you will see the oil temp drop as the engin... |
In forum General Discussion |
2 weeks ago |
|
RE: Early 2020 SR3 XX with FSW_R wheel - Looking for confirmation Looking forward to what you find out. A few things from my experience: - I don't have the GPS:NO CONN, have never seen that error - I have never been able to have my wheel keep time correctly, I igno... |
2 months ago | |
|
RE: New Member with SPYDER 0032 for sale on BAT I hope you get what you what out of BAT. It is a cool car. |
In forum New Member Introductions |
3 months ago |
|
RE: URGENT: SR3XX with 1500 - Fuel PR issue I think I am at the end of my investigation here. A few other learnings from me: - The fuel pressure (FP) at idle should be ~3.3 Bar at idle as noted in the manual - My regulator has a tendency to dri... |
In forum General Discussion |
5 months ago |
|
RE: RPE V8 website Thanks for sharing |
In forum SR8 Specific Discussion |
5 months ago |
|
RE: SR3 1300cc no spark Great to hear you fixed it. Putting this here for others in case they also have a no spark issue. I had a similar problem a few weeks ago on a 2022 SR3XX. The issue was that the crankshaft sensor wiri... |
In forum How To / DIY Discussions |
5 months ago |
|
RE: CAN topology of the XX PDM, GPS, Camera and steering wheel Thanks, took the panel screw out but it wouldn’t come off. Doesn’t seem like there is a lot of slack in the cable. Will try again and loosen the side pod so I can move it partially out of the way. Fru... |
6 months ago | |
|
RE: CAN topology of the XX PDM, GPS, Camera and steering wheel Is the PDM mounted in the left side of the cockpit behind the access panel? today, while working on configurations the barrel connector on my data cable came loose and I believe it shorted out the us... |
6 months ago | |
|
RE: FUEL PUMP AND AIR PUMP WILL NOT COME ON. PLS HELP I would grab a multi-meter and start tracing wires back to source. In my 2022 (left hand drive) I did not have any electrical under the right side pod, all is behind the dash and in the left side pod.... |
In forum General Discussion |
9 months ago |
|
RE: CAN topology of the XX PDM, GPS, Camera and steering wheel Pulling this thread up to the top. I have a SR3xx with the AIM PDM, SW4 wheel, and TPMS. I can’t get the PDM to communicate with the wheel for the TPMS. Radical set it up so that one info page on the ... |
10 months ago | |
|
RE: URGENT: SR3XX with 1500 - Fuel PR issue We dug into the car yesterday and found a few things although no “smoking gun”. I have a fuel cell, not an aluminum tank. There was half a gallon or a gallon in the cell when we dumped it out which t... |
In forum General Discussion |
10 months ago |