Trailbrake
trailbrake
@trailbrake
Trusted Member
Joined: February 11, 2019 6:44 pm
Last seen: April 9, 2025 12:52 pm
Topics: 2 / Replies: 45
Reply
RE: Have i already broken my starter motor?

The rumors of my demise have great been exagerated! 🤣 It sounds like the input board might be damaged. The PDM would have to go back t...

6 months ago
Reply
RE: Smartycam HD Lens element order

The gasket will have to come from AiM. You're best best bet is probably to send the camera into AiM and let them check it out. They can hopefully get ...

11 months ago
Reply
RE: Smartycam HD Lens element order

It sounds like you have it further apart than a user would normally take it apart. If you took out the main lens, it will need to be focused as well. ...

11 months ago
Reply
RE: Installing Smartycam 3 Dual in Radical XX?

The Dual needs a separate power input in addition to the 5 pin 712 connection. The cable that connects to the SC3 Sport will plug into the Dual. Power...

3 years ago
Reply
RE: Help with data problems on new Radical

I'm just seeing this thread. The Radical and AiM integration are a difficult issue. To start defining things, it's important to know the players - AiM...

3 years ago
Reply
RE: Aim MXL2 dash

The MXL2 has been discontinued, so there are no deals on them 🙁 I do have all the other AiM dashes in stock and am happy to help out. I usually do Bl...

3 years ago
Reply
RE: CAN topology of the XX PDM, GPS, Camera and steering wheel

As far as I know, the FSW is the same, but I'm not an expert on the Radical install. If you call and ask the guys at AiM, they will be able to make su...

3 years ago
Reply
RE: Configuration for AIM System

What dash do you have? Strada dashes do not log, so I assume you have the Strada Logging module with the SD card? I would start with moving the beacon...

3 years ago
Reply
RE: PDM, smartycam and the XX wheel - how to configure?

There have been some FW problems with the SLM on different systems. You can try unplugging it from the system and powering the PDM, then plugging in t...

3 years ago
Reply
RE: PDM, smartycam and the XX wheel - how to configure?

Think of it has 3 separate systems. You have found the way to connect to the PDM. The SCHD is connected with the USB Mini connector next to the SD car...

4 years ago
Reply
RE: SR3 XX - Can’t see dash (out of line of sight)

The GS Dash is a slave to the PDM. Depending on the wiring in the car, it would need a data hub. The GS Dash is then just programmed as a CAN Expansio...

4 years ago
Reply
RE: SR3 XX - Can’t see dash (out of line of sight)

The shift lights would be just like in the above example. I haven't plugged into an SR3 XX yet, but it should configure just like the video above show...

4 years ago
Reply
RE: Tire Temperature Sensors on SR3-RSX and SR3-XX

Hey guys - talking to AiM, there isn't much of a standard for how the data portion of the cars was handled. For the SR3-XX, it has a PDM in it. I beli...

4 years ago
Reply
RE: Connecting/configuring smartycam

On the PDM, change the Smartycam feed to GPS Speed. Then you will get GPS speed into the camera. It sounds like you have a either bad wheel speed sens...

4 years ago
Reply
RE: Connecting/configuring smartycam

So you have a PDM32, Radical wheel, and SCHD GP 2.2. The first thing to do with all the components is make sure the FW is up to date. Then, make sure ...

4 years ago
Page 1 / 4