Liked Forum Posts
|
RE: How many use custom seat inserts and where do you have them made? Here is my second go at a bead seat. The first try I used the BSS small kit according to their recommendation. That kit would have been fine if you were just looking to only create back support but lo... |
In forum Safety Gear Discussion |
6 years ago |
|
RE: Braid I have seen sets posted on Racecarsdirect.com every now and then. |
In forum SR1 / SR4 Specific Discussions |
6 years ago |
|
RE: Stall - what next? I've just seen this section in one of the manuals: "As with any race car, it is important to put the car in neutral and release the clutch when stationary. This will significantly reduce the clutch be... |
In forum SR8 Specific Discussion |
6 years ago |
|
RE: Dry sump...new installation @charleyhradicalsportscarregistry-com every time I post something on here you are always there to help, legend! Thanks, that helps a lot! |
In forum General Discussion |
6 years ago |
|
RE: Wiring diagram of the Radical Dash Connector Hi Charley, all the wiring is done, all sensors are working except the gear sensor, there i still have to tinker around a little bit. Here some picture as promised: Attachment : E96AE907-2704-496A... |
7 years ago | |
|
RE: Chain for SR1 @johnsopathe photo of the chain breaker is of only one of the parts. It is the tool pin that pushes out the chain pin. here is the whole tool |
In forum SR1 / SR4 Specific Discussions |
6 years ago |
|
RE: Radical Gelcoat Color codes Hi Charley, thanks for collecting these. I believe my SR4 is what Radical calls "Rosso" or "Ferrari" red. But in checking around, there are several different Ferrari Rosso colors (Chiaro, Corsa, Din... |
In forum General Discussion |
6 years ago |
|
RE: Side Pod Removal on SR3 / 8 I'll add a few differences for the 1st gen SR3's. 1. The radiator is not bolted in top/bottom. It comes out by sliding it out once the side pod is removed. You need to disconnect the top and bottom ho... |
In forum How To / DIY Discussions |
6 years ago |
|
RE: Noisy Compressor motor Thanks Charley. I have contacted Radical, I have seen on their shop that they sell a motor assembly. They have not got back to me with a price yet. But, I contacted Parvalux and they quoted me aroun... |
In forum How To / DIY Discussions |
6 years ago |
|
RE: Chain for SR1 A big thank you to both of you, Greame and Charley, I will be able to order, I did not know the radicalonline. Cordially. Christian. "Christian rib ortega is on face book" |
In forum SR1 / SR4 Specific Discussions |
6 years ago |
|
RE: Chain for SR1 530 DID ZVMX 72 links. get a “rivet style” master link and the tool to install it you can buy a 150 link chain for about $150, from many motorcycle suppliers. Then you have two chains. |
In forum SR1 / SR4 Specific Discussions |
6 years ago |
|
RE: Sad Radical Hi All A few photos Attachment : IMG_1091.jpg Attachment : IMG_1090.jpg Attachment : IMG_1096.jpg Attachment : IMG_1089.jpg Attachment : IMG_1092.jpg Attachment :... |
In forum New Member Introductions |
6 years ago |
|
RE: Sad Radical Hi Nikki. We will just have to sit tight and wait,its painful i know i have looked at about 1000 concept cars on the internet and still cant find it. Paul. |
In forum New Member Introductions |
6 years ago |
|
RE: Sad Radical I keep refreshing the "Ask Phil" page but still see no new article... 😉 No pressure Charley... 🤣 😆 |
In forum New Member Introductions |
6 years ago |
|
RE: Is this safe? Here it is, you are fine John! Radical mounts in the engine shop are all on that face! |
In forum SR8 Specific Discussion |
6 years ago |