Liked Forum Posts
|
RE: REBUILD of my SR3 1300 @garagenwerke …. Yes. That’s the reverse gear ‘detent’ holder im not sure where you would buy one, but here’s a picture of mine when I had it out to shorten the spring. It’s actually not a ball bearin... |
In forum SR3 Specific Discussions |
5 years ago |
|
RE: Suspension logging & laser ride height logging I asked RaceCraft HQ if the laser sensors obviated the need for the suspension sensors. Here is what he said: Hi Phil, they are both useful in their own ways, but in brief- The laser ride heights a... |
In forum General Discussion |
5 years ago |
|
RE: New owner from Chicagoland @jswilson87 That red is gorgeous. Post some more pics. Congratulations! |
In forum New Member Introductions |
5 years ago |
|
RE: Helmet Suggestions I received a Stilo ST5 GT. My glasses went on but the cheeks are too tight. The cheek pads are 30mm. I have asked for both the 20 and 25mm. I am sure one of them will cure the problem. |
In forum General Discussion |
5 years ago |
|
RE: Factory Graphics - Custom Graphics - PPF Here is what I did Attachment : 428BB932-1F0A-416D-B93D-38A8EAB36300.jpeg Attachment : 5F31621E-70B8-443D-BB90-664E0F3CFA7C.jpeg |
In forum General Discussion |
5 years ago |
|
RE: SR3 car cover Mine works fine on my SR8 RS as well. |
In forum SR3 Specific Discussions |
5 years ago |
|
RE: REBUILD of my SR3 1300 @charleyhradicalsportscarregistry-com hey C. he is missing that cap, i told him to order it so he has the spring tension to the axle, but he was a bit confused how to put the cable on to the axle... |
In forum SR3 Specific Discussions |
5 years ago |
|
RE: Brake bias question G'day @maxltv I'm not sure I can answer your question completely, but I can tell you that my SR3RSX does the same thing.... so at least for our cars this seems 'normal' The below table has been share... |
In forum General Discussion |
5 years ago |
|
RE: SR3 car cover As a follow-up, my cover works very well on newer SR3 XX also. |
In forum SR3 Specific Discussions |
5 years ago |
|
RE: REBUILD of my SR3 1300 @garagenwerke Do you already have a connector labelled for air temp? If not then this connector could be for that. Is the extra water temp wire you have just a single wire with a spade connector on? ... |
In forum SR3 Specific Discussions |
5 years ago |
|
RE: Suspension logging & laser ride height logging Just found this video on laser ride height. Question is does the laser ride height option obviate the need for the suspension sensor logging. |
In forum General Discussion |
5 years ago |
|
RE: Suspension logging & laser ride height logging Found the video on youtube. Very informative re suspension dampers and analysis. I think I may option this on my new SR10 before the order locks. |
In forum General Discussion |
5 years ago |
|
RE: REBUILD of my SR3 1300 @garagenwerke I would recommend using a Gen 2 clutch basket as it is much stronger. Heavy duty clutch springs are a must due to the weight of the car, you should be able to find them anywhere that se... |
In forum SR3 Specific Discussions |
5 years ago |
|
RE: Running E85 in small % @raider89 Dan -- you need to find out exactly what kind of gasoline you're using. Is it Sunoco GT 260? GT 260 Plus? Or are you using leaded race gas? Have a look here... this chart lists the Sunoco ga... |
In forum General Discussion |
5 years ago |
|
RE: Suspension logging & laser ride height logging @johnannz Very exciting! I have to wait until October for mine. Where is your home track? |
In forum General Discussion |
5 years ago |