Liked Forum Posts
|
RE: How to remove the oil tank? @rojid That is unfortunate. I looked at my car a little closer with the side pod off; it looks like a tricky task. You will need to lift the car sufficiently so that the tank can be brought down th... |
In forum How To / DIY Discussions |
4 years ago |
|
RE: LIFING: suspension bushings? I tore my suspension apart this past summer, with the intention of replacing all the bushings. After inspecting them, I couldn't find any obvious wear, so I cleaned them and put them back with some CV... |
In forum How To / DIY Discussions |
4 years ago |
|
Radical electrical parts are a JOKE! As many have seen from my other post on recent TPS and ACT sensor issues after engine rebuild. What a racket. Maybe I was just lucky with my first ~15 months with SR3XX with no problems, but am scar... |
In forum General Discussion |
4 years ago |
|
RE: How to remove the oil tank? @rjbender Oops. Thanks for catching Rod. |
In forum How To / DIY Discussions |
4 years ago |
|
RE: SR3 gen 2 wet weight? This is I believe is accurate, all body panels on, 30L of fuel. Most of my weights are with driver and no bodywork but I'm 99% sure this is just car dropped on scales due to an argument with the chief... |
4 years ago | |
|
RE: Something broke today Well apparently it was not a problem, first session out was a tremendous amount of fun. Attachment : PXL_20221010_154608161.jpg Attachment : PXL_20221010_170450307.jpg Attachment : P... |
In forum SR3 Specific Discussions |
4 years ago |
|
RE: LIFING: suspension bushings? I don't have experience replacing bushings yet, however I have a plan to strip all of my suspension components and bushings at the end of the season (now), when I will visually inspect each bushing in... |
In forum How To / DIY Discussions |
4 years ago |
|
RE: RC) file uscalibration (.Led in this car and any available data logs? Here 2 pictures of up and down shift from the movie Attachment : EFFB0A6A-0217-4262-818A-166B6DB5E190.jpeg Attachment : 164B8851-8F19-4BB5-A696-2D2879E3FF8C.jpeg |
4 years ago | |
|
RE: RC) file uscalibration (.Led in this car and any available data logs? @kuddby-racing, the pictures you posted are very helpful. As Dan mentioned your paddle system is a Geartronics system. Unfortunately I don't have a wiring diagram for that system but if you reach ou... |
4 years ago | |
|
RE: Something broke today Washed and ready for full test day next Monday! Attachment : PXL_20221002_193705091.jpg |
In forum SR3 Specific Discussions |
4 years ago |
|
RE: Something broke today I would say I have been rather successful in this rebuild. Started up just fine runs fine and cycles through the gears just fine. On Sunday I plan to blast up the street to see how it is under load ... |
In forum SR3 Specific Discussions |
4 years ago |
|
RE: Something broke today Thank you Sir! |
In forum SR3 Specific Discussions |
4 years ago |
|
RE: Track videos Back at oulton park for a proper go, after the first time was cut short with my rectifier blowing. Track was fully wet all morning then finally the intermittent showers stopped, the clouds broke, and... |
In forum Track / Race Videos |
4 years ago |
|
RE: General prep after a wet day? I don't run cars so not the best person to answer this but personally I would be going over the car with ACF50. Its a water replant that protects from corrosion etc. The only thing to avoid with this... |
In forum General Discussion |
4 years ago |
|
RE: GDU mechanics and 1st gear selection As mentioned this is normal, due to the design of the gearbox. The gears all have 'dogs' on which engage with each other as you shift gear. This all works well as the gears and shafts are all spinning... |
In forum General Discussion |
4 years ago |