Liked Forum Posts
|
RE: Suspension logging & laser ride height logging John - I would love to but as the caregiver for the mrs, I do not have a hall pass. I only get one when back in CA and one of the kids take over my duties. But thanks for the invite. Phil |
In forum General Discussion |
5 years ago |
|
RE: Brake bias question Mine behaves the same as well - but I honestly don't pay much attention to what the setting is and just dial it forward as needed. The more 6th - 2nd gear braking corners on a track, the more I dial i... |
In forum General Discussion |
5 years ago |
|
RE: New owner from Chicagoland Welcome Jeff (@jswilson87)! Congratulations on the new car. |
In forum New Member Introductions |
5 years ago |
|
New owner from Chicagoland 2021 Attachment : C3ED687A-A58D-402B-8042-605427158C79.jpeg Chassis #SR301332 |
In forum New Member Introductions |
5 years ago |
|
RE: REBUILD of my SR3 1300 @garagenwerke, I don’t know if this is your issue, but if you have the reverse cable connected properly and the lever is hard to operate, meaning the GDU is hard to put in reverse, it can be an indica... |
In forum SR3 Specific Discussions |
5 years ago |
|
RE: SR3 car cover As a follow-up, my cover works very well on newer SR3 XX also. |
In forum SR3 Specific Discussions |
5 years ago |
|
RE: REBUILD of my SR3 1300 Hi Guys! As is said, it's runing. Oilpressure works ... 🙂 GDU is in place and refilled with oil, oilpump in the GDU is working, too. > Next step is to install the reverse gear cable. Question: h... |
In forum SR3 Specific Discussions |
5 years ago |
|
RE: Hello from Germany / sr3 Yes another rebuild! I had a feeling we would start seeing some more. Welcome! |
In forum New Member Introductions |
5 years ago |
|
RE: Hello from Germany / sr3 @garagenwerke welcome! Your car looks great and is coming along very well There are plenty of people here to help you with you project. 🙂 |
In forum New Member Introductions |
5 years ago |
|
Hello from Germany / sr3 Hi from Germany 🇩🇪 My name is Adrian, 35 years old. I bought a radical sr3 in / used / condition. Bodywork bad, engine removed with a broken rod and so on. I am actually rebuilding i... |
In forum New Member Introductions |
5 years ago |
|
RSR Photo Contest #1 Winners Thank you to everyone for submitting your Radical Photos for our 1st contest. This was a tough decision because they were all so good. After considerable deliberation The winners are.... Tall-Joh... |
In forum General Discussion |
5 years ago |
|
RE: Pineview Run All Time Track Record Great job Jonathan! Smashing the track record is a great way to show what an amazing performance value Radicals are. You can’t go faster for less! 🙂 |
In forum Track / Race Videos |
5 years ago |
|
RE: Connecting/configuring smartycam On the PDM, change the Smartycam feed to GPS Speed. Then you will get GPS speed into the camera. It sounds like you have a either bad wheel speed sensor or a bad config on that. I don't know which se... |
5 years ago | |
|
RE: Connecting/configuring smartycam @trailbrake This has been very helpful! I took a look at the data - and sure enough, there is no data under R_frSpeed. GPS_Speed data, however, is there. (is this expected behavior?). Presumably, ... |
5 years ago | |
|
RE: Connecting/configuring smartycam @trailbrake - Thanks!! After playing around a bit - it seems that to configure the SmartyCam, I have to connect to the camera with a USB - miniUSB. But I'm not sure I've accomplished anything in ... |
5 years ago |