Liked Forum Posts
|
RE: CAN topology of the XX PDM, GPS, Camera and steering wheel not sure if this is directly relevant to the thread but I've spent a while looking at the wiring on my car, which is all XX - - the radical wiring loom does allow you to utilise all the PDM's expansi... |
4 years ago | |
|
RE: PDM, smartycam and the XX wheel - how to configure? to wrap up this thread..........the answer is that you need a cable from radical which allows you to connect the wheel directly to RS3 via USB. part number LH0377. It's a female deutsch connector on... |
4 years ago | |
|
RE: Big Brakes Posted by: @pbc223 Does anyone know when the big brake upgrades will be available? It would be nice to install them before the snow melts. They must be orderable now. My race shop is working up a ... |
In forum SR 10 Specific Discussion |
4 years ago |
|
RE: Big Brakes I saw them on a new sr10 here in Korea last week, so it seems like they're shipping from the factory |
In forum SR 10 Specific Discussion |
4 years ago |
|
Dry sump , uprights, muffler For sale Attachment : A6438560-ABD9-4245-BD4B-B028F04615FE.jpeg Attachment : 70D106F4-E55F-4ECE-9747-F2C4158CC9C4.jpeg Attachment : 27278C12-8ED6-4F3A-B2C9-2E9F8304C78A.jpeg Attachment : ... |
In forum Radical Parts For Sale / Wanted |
5 years ago |
|
RE: Suspension question The the silver ring in your second picture is the spring perch which is used to adjust preload and corner weighting. If there is some sort of set screw on that perch, it is probably used to prevent i... |
In forum General Discussion |
4 years ago |
|
RE: Bearing failure No mention of changes to the engine refresh schedule. Attached bulletin. Apparently the list of changes are: input shaft, input bearing, engine cases machined Attachment : image.png |
In forum SR3 Specific Discussions |
4 years ago |
|
RE: Bearing failure Just want to given an update on this. 5 months and 3 weeks after I ordered a new engine, it finally arrived. Radical seems to be prioritizing parts for new car builds and not replacements, so if you... |
In forum SR3 Specific Discussions |
4 years ago |
|
RE: Engine rebuilt time or not? I ran my engine to 55 hours this past season, but after taking the car to the shop, they said I was about to lose the shifter. I guess I was at the absolute limit. |
In forum General Discussion |
4 years ago |
|
RE: Ramp truck for radical Yeah I like the aluma open with the front piece. I was going to put a trailer in the garage just barely fitting but only a 7ft wide trailer would fit and that’s just too little clearance for the radic... |
In forum Towing / Trailers / Truck Discussion |
4 years ago |
|
RE: Ramp truck for radical I love that. I thought about getting something like that as well (like the flatbeds Carvana uses) because our HOA doesn't allow trailers either. However, my garage is down a hill from the driveway s... |
In forum Towing / Trailers / Truck Discussion |
4 years ago |
|
RE: CAN topology of the XX PDM, GPS, Camera and steering wheel I think I mostly figured out how the XX , FSW setup works last night. The main logger-brain is the PDM32. It has logging, WIFI, USB, ECU, Smartycam and receives all the analogue sensors (suspension... |
4 years ago | |
|
RE: Newest SR3XX Steering Wheel? Just heard back from the dealership and the black button design wheel is the new wheel moving forward. |
In forum General Discussion |
4 years ago |
|
RE: Hello from Virginia Some pics of the new wheel position. Attachment : IMG_8473.jpg Attachment : IMG_8472.jpg |
In forum New Member Introductions |
4 years ago |
|
RE: Tying down a radical Posted by: @bill-snead Hello- Anyone have a recommendation on a good brand of tie down ratchet straps? So many out there. I will be using the hub tie down locations. Thanks! Hard to go wrong with Ma... |
In forum Towing / Trailers / Truck Discussion |
4 years ago |