Forum Replies Created
|
RE: Hi Everyone Welcome! It is great to meet you. |
In forum New Member Introductions |
4 years ago |
|
RE: Different seat? Hi @slowcar, Radical sells single seats and there is a company in the UK called The Ark Angels that offers one also. But converting to a center seat configuration is a bigger job than it seams. You ... |
In forum General Discussion |
4 years ago |
|
RE: Prosport Body Molds @kt-r13, Nigel doesn’t have these anymore. |
4 years ago | |
|
RE: Hi from NorCal! Hi Ivan (@istro), welcome! Glad to hear Graeme’s car is in good hands. I’m looking forward to hearing more about your car. |
In forum New Member Introductions |
4 years ago |
|
RE: Ramp truck for radical You should be able to make that work. You need a ramp angle of less than 3 degrees. The only downside of an open trailer is if you need to stay overnight on the road, you don’t get the same level of... |
In forum Towing / Trailers / Truck Discussion |
4 years ago |
|
RE: Hello from Virginia Thank you Danyel (@wisko-racing), this is great news. Hopefully they will figure out a retrofit for the LHD cars also. And Welcome! I am glad to see you posting. 🙂 |
In forum New Member Introductions |
4 years ago |
|
RE: Newest SR3XX Steering Wheel? @drugg1st, Very strange. I am interested to hear what they say. Congratulations on your new car! What chassis is your car? Is it in the Registry yet? |
In forum General Discussion |
4 years ago |
|
RE: Newest SR3XX Steering Wheel? That is interesting, I have never seen one with the black buttons on it. Did you ask the dealer about it? There have been quite a few shortages with Aim lately and I know that in the past when there ... |
In forum General Discussion |
4 years ago |
|
RE: Left sidepod hanging lower than the other...not obvious why.. My thoughts mirror David’s. I would start by checking the chassis height to determine if this is due to suspension alignment or if the side pod is mounted differently for some reason. |
In forum General Discussion |
4 years ago |
|
RE: RSX gen3 updated bodywork onto gen2 SR3 Yes, I know that car well. 🙂 When you described it I was wondering if it was 563. I am a little surprised that Scott sold it already. Pricing on the rear body is highly dependent on condit... |
In forum General Discussion |
4 years ago |
|
RE: RSX gen3 updated bodywork onto gen2 SR3 Hi Willem (@illwillem) welcome! What chassis number car do you have? I haven’t done the change over but it sounds like you have the parts list about right. You could likely modify your current tail... |
In forum General Discussion |
4 years ago |
|
RE: Help again: clutch problem @raider89, I haven't heard of any systemic cause for this failure and I suspect that nothing that you did caused the failure. Perhaps @RLM-dan had more details? It is my understanding that this just... |
In forum General Discussion |
4 years ago |
|
RE: Front light LED's/DRL's - wiring loom? Hi @rojid, As David said, for an RSX or an XX there would be a round connector in the location that he showed. For the Gen 1 and 2 cars there is a rectangular connector in the front left wheel well. ... |
In forum General Discussion |
4 years ago |
|
RE: New 1500cc Hayabusa engine starts briefly then dies Now the ECU should have enough data to point to what is going on. I would recommend downloading the ECU data and sending it to Spring Mountain. |
In forum General Discussion |
4 years ago |
|
RE: Engine rebuilt time or not? Posted by: @raider89 10,700 if I remember correctly That isn’t much of an over rev. I would definitely recommend contacting Spring Mountain to get their advice. I wouldn’t recommend putting three... |
In forum General Discussion |
4 years ago |