This user account status is Approved

Liked Forum Posts

RE: First 6hr Service on SR10 - Lessons Learned

Done Deal. That Tripod pod specific grease is very loose and light counter intuitive to what you'd think should be in there. Hope it works Attachment : IMG_0717.jpeg

In forum How To / DIY Discussions

4 years ago
RE: First 6hr Service on SR10 - Lessons Learned

Good information. I really appreciate it when someone takes the time to post what the've learned and lets you know where to get what's needed. One my 2021 SR10 and the new 2022 I just got I've had the...

In forum How To / DIY Discussions

4 years ago
RE: Side Pod Removal on SR3 / 8

To follow up from my last post, I went ahead and drained some fluid from the GDU cooling circuit, removed the cooler lines and blocked them off in order to remove the right side pod. With the pod off ...

In forum How To / DIY Discussions

4 years ago
RE: First 6hr Service on SR10 - Lessons Learned

@parsonsj For what it's worth when I was talking to a Radical tech about the repacking process, they emphasized getting grease in the rollers. They had a special tool that they use to do this but I d...

In forum How To / DIY Discussions

4 years ago
RE: First 6hr Service on SR10 - Lessons Learned

@raider89 Right! If you read the actual procedure (from one of the guides here in the Resource Library), it says nothing about working grease through the rollers. Just wipe everything clean, put new g...

In forum How To / DIY Discussions

4 years ago
RE: First 6hr Service on SR10 - Lessons Learned

@davidf Seems like the tool can be a real time-saver over my method of working the grease into place via hand. My guess is that the SR10 and SR8 use the same diameter tripods (bigger than the SR3), bu...

In forum How To / DIY Discussions

4 years ago
RE: First 6hr Service on SR10 - Lessons Learned

@rjbender Rod I am using run time but you make a good point. The manual says "every 10 hours of running" which probably means in gear and rolling. I have heard of more frequent driveshaft failures...

In forum How To / DIY Discussions

4 years ago
RE: First 6hr Service on SR10 - Lessons Learned

@rjbender GKN makes tripod axle joints for many race cars and non race cars, and they sell GKN tripod grease. From PegasusAutoRacing.com: This grease is designed specifically for use in tripod join...

In forum How To / DIY Discussions

4 years ago
RE: First 6hr Service on SR10 - Lessons Learned

Tripod joint greasing tool. Fits snugly over the roller joint, has a grease gun fitting on the back. Attachment : image.png

In forum How To / DIY Discussions

4 years ago
RE: SR3XX 1500cc oil cooler spec?

Nope, never did. My engine is out at SM for rebuild right now. When I asked dealer for more information about aftermarket vs Radical preferred brand, they said I need to stick with Radical because t...

In forum How To / DIY Discussions

4 years ago
RE: Compressor Receiver Water Drain Interval

@raider89 - G'day Dan, No - the air line that runs to the back of the car and feeds the solenoid block looks like it comes off the top of the compressors storage receiver (which is where it should be ...

In forum How To / DIY Discussions

4 years ago
RXC for sale on Bringatrailer

My 2014 RXC Coupe V6 is listed for sale on bringatrailer for anyone who may be interested. Attachment : IMG_0864.PNG Attachment : Radical RXC uphill esses at VIR.JPG

In forum RXC Specific Discussions

4 years ago
RE: Used Tires

I still have several sets of lightly used Radical tires listed in the parts for sale on this site. New listing for set of wheels plus set of 5-heat-cycle used tires mounted and balanced, just added. ...

In forum Radical Parts For Sale / Wanted

4 years ago
RE: First 6hr Service on SR10 - Lessons Learned

Posted by: @clark-darrah You cannot find the Radical recommended grease (Total Lithium EP2 400g) so I used Lucas Oil Red N Tacky which is what my Radical dealer uses. The correct grease is GKN Trip...

In forum How To / DIY Discussions

4 years ago
First 6hr Service on SR10 - Lessons Learned

Thought I would post my experience having completed the 6 hour service on my SR10. By way of background I'm fairly competent doing basic service stuff on my other cars (engine, trans, diff oil change...

In forum How To / DIY Discussions

4 years ago
Page 43 / 140