Owner of Radical SR3 RSX and SR3 XX
This user account status is Approved

Liked Forum Posts

RE: Something broke today

Attachment : PXL_20220910_061006651.jpg

In forum SR3 Specific Discussions

4 years ago
RE: My battery issues won't die.... how to troubleshoot?

well i fixed this. Ricksmotorsport is a wonderful resource and has howto guides for noobs like me, to diagnose the different components that make up the charging system on a bike engine. i simply fol...

In forum General Discussion

4 years ago
RE: Wheel Speed Sensor

I don't think there is a trick. The owner's manual says it should be no closer than 2mm from the brake disc bolts. I installed one and I may have put it a little closer than that and it works well.

In forum How To / DIY Discussions

4 years ago
RE: Power Steering- RXC/SR10

Issue sorted! Reached out to Radical and they advised to check the EPAS ECU 31 pin plug. I found 12V at pin 1-2 as required and the harness was fine. There was no power going from the ECU to the Motor...

In forum How To / DIY Discussions

4 years ago
Rapture Registry Added

The Rapture Registry was just added... Take a look. 🙂

In forum General Discussion

4 years ago
RE: Something broke today

Early Busa's (99-01) didn't have these washers fitted as standard but everything else did. Radical leave them in everything and fit them to engines without them to assist. Having said that you should ...

In forum SR3 Specific Discussions

4 years ago
RE: Compressor Receiver Water Drain Interval

@rjbender Great info. Thanks Rod!

In forum How To / DIY Discussions

4 years ago
RE: Removing Oil Lines

@clark-darrah My only concern about how they did this is the possibility of stripping the threads.

In forum How To / DIY Discussions

4 years ago
RE: Anyone rebuild a JLS airjack?

@99sh, it isn’t uncommon for the jack mounting structures to get bent from “off track excursions “…

In forum How To / DIY Discussions

4 years ago
RE: Quickest way to change balance?

Rake plays a significant role in the understeer/oversteer characteristics. More positive rake (when rear ride height is greater than front) results in less understeer or more oversteer at high speeds...

In forum Suspension setup and Handling discussion

4 years ago
RE: Replacing discs DIY?

Hmm, another misprint? The factory does not safety-wire the hat to disc bolts at least on the newer cars because the bolts are fastened with a lock nut on the other side. If these were threaded into...

In forum How To / DIY Discussions

4 years ago
RE: Anyone rebuild a JLS airjack?

Perfect, thank you for the pictures. Looks very straight forward. Like you said the hard part is getting it out! Googling that part #, I see it in their 2013 catalog. Same PN for 52mm units. Thank...

In forum How To / DIY Discussions

4 years ago
RE: Anyone rebuild a JLS airjack?

@99sh, Yes I purchased the rebuild kit from XRP. For my SR3 the XRP part number for the kit was 870001. One kit is required for each cylinder. I also replaced the 2 washers (per cylinder) that are...

In forum How To / DIY Discussions

4 years ago
RE: Anyone with Radical Rental Prices

It might be helpful to unpack what you are receiving for the 8K. I can estimate some of the prices in USD which might be similar to UK prices. set of new Hankook C52 compound slicks $1500. (low use ...

In forum General Discussion

4 years ago
RE: Something broke today

Conversation pcs for the wall of shame. Attachment : PXL_20220804_043202293.jpg Attachment : PXL_20220804_043208310.jpg

In forum SR3 Specific Discussions

4 years ago
Page 37 / 67